Results 1 to 7 of 7

Topic: G25 and cronusmax plus unstable

  1. #1
    Babyfaced Assassin

    User Info Menu

    G25 and cronusmax plus unstable

    Hi:

    I have cronusmax plus (v. 1.24) with G25 on ps4. I followed the instructions to set it up and it works, but sometimes when i connect G25 and start to calibrate the wheel, it does not finish the action and stay turned on the left. If i turn on the game (gran turismo sport), all the bottoms works except the wheel.

    I have other problem. When I connect g25 and it calibrates well and start the game, sometimes the wheel loses the calibration. This happens when i have an accident.

    Sorry for my english, im spanish

    Best regards

  2. #2
    Support Staff

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Check to see if you are on latest firmware for your G25. If your wheel isn't calibrating correctly on startup, then that sounds like an issue with the wheel itself, as you should be able to calibrate it correctly without it plugged into the CronusMax.

  3. #3
    My Other Ride Is a Yoshi

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Quote Originally Posted by Picklock View Post
    Check to see if you are on latest firmware for your G25. If your wheel isn't calibrating correctly on startup, then that sounds like an issue with the wheel itself, as you should be able to calibrate it correctly without it plugged into the CronusMax.
    Same Problem here. First i thought it belongs to driving fails.. then i found out, that this is happening about 8 minutes after calibration. I tested it on PS4 Pro with GT Sport, CronusMaxPlus V3, G25 and GT Force Pro.

    Newest Firmware is installed and op mode is WE. I tested all thinkable combinations in the config.. everytime after 8 minutes it fails..

    any ideas?

  4. #4
    Support Staff

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Quote Originally Posted by shadow0815 View Post
    Same Problem here. First i thought it belongs to driving fails.. then i found out, that this is happening about 8 minutes after calibration. I tested it on PS4 Pro with GT Sport, CronusMaxPlus V3, G25 and GT Force Pro.

    Newest Firmware is installed and op mode is WE. I tested all thinkable combinations in the config.. everytime after 8 minutes it fails..

    any ideas?
    If it's a reoccurring issue based on a specific amount of time, possibly this.
    http://cronusmax.com/forums/showthre...t=disconnected

  5. The Following User Says Thank You to Picklock For This Useful Post:


  6. #5
    My Other Ride Is a Yoshi

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Quote Originally Posted by Picklock View Post
    If it's a reoccurring issue based on a specific amount of time, possibly this.
    http://cronusmax.com/forums/showthre...t=disconnected
    Found it out by myself a few moments later and wanted to test ist this evening again to be sure.
    I only disconnected the controller from the ps4 an it works like a charm.


    So this is my setup (works the hole testing time of 2 hours):
    PS4 Pro
    GT Sports
    G25 (with pedals only this time)
    CronusMax+V3 1.24 WE settings like these http://cronusmax.com/manual/racing_w...ing_to_ps4.htm
    DS4 V1 i think (PS1 25th anniversary Edition) - switched off
    compatible usb-hub
    Controls are done with another DS4 (V2 ?), thas was connected wireless.


    I'll give it a try and switch the controllers this evening (it is now 06:30 am in germany). The newer version of the controller is able to communicate through usb, we will see if it works.

    Thanks for the quick answer.

    Kind regards
    Last edited by shadow0815; 6th December 17 at 01:42.

  7. #6
    Support Staff

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Quote Originally Posted by shadow0815 View Post
    Found it out by myself a few moments later and wanted to test ist this evening again to be sure.
    I only disconnected the controller from the ps4 an it works like a charm.


    So this is my setup (works the hole testing time of 2 hours):
    PS4 Pro
    GT Sports
    G25 (with pedals only this time)
    CronusMax+V3 1.24 WE settings like these http://cronusmax.com/manual/racing_w...ing_to_ps4.htm
    DS4 V1 i think (PS1 25th anniversary Edition) - switched off
    compatible usb-hub
    Controls are done with another DS4 (V2 ?), thas was connected wireless.


    I'll give it a try and switch the controllers this evening (it is now 06:30 am in germany). The newer version of the controller is able to communicate through usb, we will see if it works.

    Thanks for the quick answer.

    Kind regards
    Appreciate the update!

  8. #7
    My Other Ride Is a Yoshi

    User Info Menu

    Re: G25 and cronusmax plus unstable

    Quote Originally Posted by Picklock View Post
    Appreciate the update!
    So here is my update..

    It works with the setup i described before and it works with switched controllers (V1/V2).

    Next weekend i'll give the GT Force Pro another try.
    Also Project Cars 2 and DriveClub will find the way in the test, if them are available to me then.

  9. The Following User Says Thank You to shadow0815 For This Useful Post:


Similar Topics

  1. Quick recovery for cronusmax plus led to pc not recognizing cronusmax anymore
    By Flippride11 in forum CronusMAX PLUS Hardware Support
    Replies: 0
    Last Post: 19th February 16, 02:08
  2. Replies: 16
    Last Post: 30th November 15, 14:08
  3. Max Remapper Senstivity change unstable.(Xbox 360)
    By Khnzz in forum Cronus PRO Software Support
    Replies: 3
    Last Post: 6th July 15, 05:17
  4. MaxAim unstable behavior
    By RingKing in forum CronusMAX PLUS Keyboard & Mouse Support
    Replies: 3
    Last Post: 19th January 15, 14:19

Tags for this Topic

Posting Permissions

  • You may not post new topics
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •