Results 1 to 3 of 3

Topic: Fanatec CSR plus petals in PC mode not connecting to drive hub

  1. #1
    Babyfaced Assassin

    User Info Menu

    Fanatec CSR plus petals in PC mode not connecting to drive hub

    I have a a Fanatec CSR Plus pedals. I follow the step-by-step process to connect to the drive hub and I’m not getting the figure 8 LED changing to say CSR.
    The wheel is in PC mode, and I can get a Xbox one controller to work. But my CSR wheel is not being detected by the drive hub. I am using this on an Xbox one. The CSR wheel has updated firmware and drivers.

  2. #2
    Senior Staff

    User Info Menu

    Re: Fanatec CSR plus petals in PC mode not connecting to drive hub

    Can you check if it work on your PC and if not check the USB cable. You can also use port 3 on the DriveHub if you like.

  3. #3
    Babyfaced Assassin

    User Info Menu

    Re: Fanatec CSR plus petals in PC mode not connecting to drive hub

    I have the Drive Hub CM00076 and I think it is DEAD ON ARRIVAL, Because when I try to update the firmware, despite being plugged into my PC and the figure 8 LED on, the firmware says CANNOT FIND DEVICE.
    (Does NOT work on Mac either)

    I’ve spent over 3 hours trying to get it to work with my Fanatec Forza Motorsport CSR wheel plus pedals on an Xbox One. I know it should work and IS listed to work with this unit, but it will not show up,
    and stop the figure 8 led pattern.
    To be clear:
    I get the figure 8 patter to show it’s in race mode, but the CSR wheel, will not connect to it.
    *An xbox ONE controller will work fine through it.
    I’ve rebooted the Xbox one with a 10 second power button hold
    My micro USB cables are good - the Xbox Controller does work, but not the wheel. I've tried multiple USB Cables.
    The xbox one controller is on the latest firmware
    I make sure the xbox one controller is off when I connect it.
    My Fanatec CSR wheel IS in PC MODE
    My Fanatec CSR wheel HAS A good usb cable, and works on my PC fine
    I FOLLOW the steps here https://collectiveminds.ca/shop/allconsoles/drivehub/ to connect it.
    But the wheel never shows up, just an eternal figure 8 pattern on my drive hub.

Similar Topics

  1. PS4 Issues connecting cronusMax ,sony headset ,wireless DS4 and a hard drive.
    By JohnTheOne in forum CronusMAX PLUS Hardware Support
    Replies: 0
    Last Post: 20th February 18, 08:43
  2. [PS4] Drive Hub w fanatec csw v2 so far
    By Rs60nr1 in forum Fanatec Racing Wheels Support
    Replies: 32
    Last Post: 16th January 18, 17:10
  3. Drive hub , fanatec mode on Gt2 wheel (Ps4)
    By Thoma in forum DriveHub Hardware Support
    Replies: 8
    Last Post: 15th January 18, 20:35
  4. [PS4 PRO] Fanatec 2.5, Fanatec mode not working or DirectDrive-GT Sport
    By Juiced46 in forum Fanatec Racing Wheels Support
    Replies: 0
    Last Post: 17th December 17, 12:19
  5. [XBOX ONE] Fanatec GT2 wheel and Fanalogic Mode with Drive hub
    By Supermike78 in forum Fanatec Racing Wheels Support
    Replies: 9
    Last Post: 20th October 17, 15:36

Posting Permissions

  • You may not post new topics
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •