Logitech G25/G27 (and other supported wheels)
Connecting to PS4 (USB Hub Required)
To view a full list of Supported Racing Wheels for this guide - Click Here
Set Output Protocol
Follow the instructions here
to correctly connect your CronusMAX PLUS to a PC via the PC PROG port using the supplied Mini-USB Cable
Load Cronus PRO and go to Tools > Options > Device
Set the Output Protocol to AUTOMATIC. (IMPORTANT - If not set to AUTOMATIC then the controller will disconnect every 10 minutes).
These are also the recommended default Speed Up Settings for Logitech and Supported Wheels. Rumble Over Bluetooth is disabled as it's not being used.
Note: Make sure 'Inframe In' is disabled as there have been reports that it causes wheels to randomly disconnect if it is enabled.
Check PS4 Partial Crossover Support is Disabled
Select the CMax Plus Tab and make sure the box to the left of 'Enable PS4 partial crossover support (auto reconnect every 10 min)' is NOT checked.
You can now close the Options window and disconnect your CronusMAX PLUS from your PC.
Set Cronus Operational Mode to PS4 Wheel Edition
Your CronusMAX PLUS must be in PS4 Wheel Edition Mode
. Go to Tools > Cronus Operational Mode and select PS4 Wheel Edition. Or you can click on the Mode in the Status Bar
to bring up the Cronus Operational Mode Wizard.
After setting the Operational Mode, the Cronus PRO Status Bar
will look like this.
Prepare the USB HUB
Using a Compatible USB Hub
(USB 2.0 or lower is recommended) connect the controllers as follows:
If you do not know the USB hub port numbers, click here
for a guide on how to discover the port assignments.
Some USB Hubs prefer the Cross Over controller to be on Port 3, just make sure that when you power cycle the console that the CronusMAX PLUS completely shuts down (No LED) and doesn't sit in standby mode (Spinning Animation LED), otherwise on reboot the authorization won't work correctly. Note: To correctly shut down the console, usb hub and CronusMAX PLUS, power cycles must be done from the console, not the controller.
Connect the USB HUB to the CronusMAX PLUS
Now that your controllers are connected to the appropriate ports on the USB Hub, connect your USB Hub into the Input Port
of the CronusMAX PLUS.
Connect the CronusMAX PLUS to your PlayStation 4
Connect the CronusMAX PLUS into one of your PlayStation 4 USB ports via it's Output Port
Ready To Use
After a couple of seconds the display on the CronusMAX LED
will go from the Authentication 'AU' Animation
(or a number
if slot recall is enabled
and a script was previously loaded) - indicating that the controllers are authorized and you're ready to play. At this point you can use your Logitech G25/G27/Supported Wheel through the CronusMAX PLUS on your PS4. It's that simple!
The DS4 Authentication controller will be disabled. The lightbar will not illuminate, it will not vibrate and none of it's controls will interefere with your experience. It can safely be left sitting idle on a surface as if it was turned off. Never power on the console with the DS4 controller by pressing the PS button. Only power on the console using the console power button.
You should make sure that the DS4 wireless constroller is un-paired/de-synced from the PS4 for optimum performance. You can do this by connecting your DS4 to the PS4 via your CronusMAX with a USB cable and go to Settings > Devices > Bluetooth Devices > then click on the controller you're using (the green lit-up one) > Disconnect.
If the LED on the CronusMAX PLUS does not change from AU to a number then the authorization controller is not authenticating. 99% of the time this means either you didn't set the Output Protocol to AUTOMATIC in Step 1 of the instructions, or the Micro-USB cable to the DS4 controller is faulty or simply not compatible, you should try another one. Another issue that sometimes comes up is that the controller USB port has a loose data pin. It will charge fine, but won't transmit data.
If you find that the controller disconnects at random times, and you are sure everything is setup correctly and Inframe In is disabled in your Speed Up Settings, then the USB cable is obviousley losing its connection between the DS4 authorization controller and the CronusMAX. This can be caused by a poor quality USB cable, the USB socket on the DS4 authorization controller itself is loose, or the USB hub you are using is poor quality. Check all connections and replace any parts if necessary.